Technical disclosure of wallpaper construction of

2022-07-22
  • Detail

The decoration effect has a deep influence on the final home decoration effect of the wallpaper. No matter how good the wallpaper is, it will be destroyed by improper decoration. In order to let consumers get the best wallpaper decoration effect, moman wallpaper introduces the wallpaper construction technology in detail

the decoration effect has a deep impact on the final home decoration effect of wallpaper, and the best wallpaper will be destroyed by improper decoration. In that case, in order to let consumers get the best wallpaper decoration effect, moman wallpaper introduces the wallpaper construction technology in detail

wallpaper construction steps and detailed process introduction:

1 Before entering the construction site, first check and accept the wall treatment. If it is not the basic construction of our company, you need to fill in the basic treatment acceptance form with the customer and sign it, and then take it back to the company for filing

2. Check whether the wallpaper batch number is consistent and whether the quantity is wrong. If there is a problem with the batch number or quantity, notify the company in time and wait for the company to arrange. Do not paste the wrong wallpaper model or reverse pattern

3. Cutting paper is the key link of wallpaper pasting. The paper should be cut on a flat and clean base without more cutting, and the cut paper should be pasted in order. Note that the residual materials should be used for splicing and pasting around the door and window openings and other local walls

4. Glue brushing is the key link of wallpaper pasting. Non woven fiber wallpaper should be glued on the wall, and the width of the glue brushing should be 2.5 times the width of the wallpaper, while paper-based (wood pulp) wallpaper should be glued on the back of the paper. After gluing, the glue surface and the glue surface should be stacked and pasted after placing for 1-2 minutes. The glue brushing should not be too thick, but should be uniform

5. The principle of pasting wallpaper is first vertical and then horizontal, first up and then down, first high and then low. The first paper should be pasted from the inner corner of the wall, gently flattened from top to bottom, pressed from the middle to both sides, and then scraped with a soft plastic scraper from top to bottom, from the middle to both sides, so as to make the wallpaper stick firmly with the wall and make the wallpaper flat. It should be noted that the seam of the paper should not overlap or leave the seam, and there should be no mouth opening phenomenon. The force should be appropriate when catching bubbles in the seam, Avoid scratching or thinning the paper

6. The joints at the top of the wall and the skirting shall be tight. Use a scraper to compact it along the edge of the wall and the skirting, and then cut it with a wallpaper knife and scrape it flat. When pasting wallpaper, try not to extrude the glue from the joint. If you accidentally extrude the glue, you should immediately remove it with a clean wrung dry wet white towel or sponge, and always keep the wet towel or sponge clean and sanitary

7. When the wall meets the electrical socket switch, you can gently apply the wallpaper on it, find the center point, cut the cross from the center, then cut off the excess part with a wallpaper knife, and scrape it flat along the socket and switch panel with a scraper

8. The materials used require authentic brand putty and protective agent provided by the company. If the customer requires to use other brands of putty or varnish, please contact the company for negotiation. Workers are not allowed to negotiate pricing with the customer privately

9. Before construction, the base course should be checked and cleaned first. In case of large-area hollowing, delamination and cracks, the company should be notified in time to negotiate with the customer for settlement

10. The construction process must ensure that one layer of sealant is used to seal the bottom, one layer of putty is applied after leveling and corner finding, and the second layer of putty is applied after the air is dry and polished. The next layer of putty is not allowed to be applied until the last layer of putty is dry, so as to avoid hollowing and cracking of the wall. Finally, after polishing and leveling, brush a layer of protective agent to prevent moisture. Pay attention not to pollute the ceiling, door pocket and other places with protective agent. (in case of contact between base layers of different materials, kraft paper tape or other crack prevention treatment must be pasted before the bottom layer treatment, and the insulation wall needs to be pasted.)

11. After the bottom layer is treated, it must be ensured that the internal and external corners are straight and free of collapse; The wall is smooth, solid, flat and smooth; No cracks, hollows, sand holes and putty are required

12. Do moisture-proof treatment, brush protective agent or varnish once, and the proportion shall be implemented according to the "construction rules of moman series wallpaper"

based on the best wallpaper products obtained by consumers, moman arranges the most detailed construction process for consumers to help consumers obtain the best wallpaper and the most satisfactory decoration effect

成都性病医院

长沙肿瘤医院

潍坊男科医院

石家庄男科医院

Copyright © 2011 JIN SHI